[Galaxy S III][IMPORTANT] GT-I9300 Hard Brick Fix

1. Copying the Bootloader file to an external SD Card, using a normal GT-I9300.
2. Inserting the external SD card into the bricked phone, and copying the bootloader file to the defective PBA.
3. After downloading the bootloader file to the defective phone, entering download mode with the phone, and downloading a Full S/W.(PIT, PDA, CSC, PHONE files)

• (12-38)_GT-I9300_BRICKED.pdf.zip - This ZIP file Contains a PDF file that is the manual for the fix.
• GT-I9300_Boot_Recovery.tar - This TAR file is the Bootloader that is copied to the external SD card.
• Odin3v3.07.rar - The program specified in the manual that copies the bootloader onto the external SD card.
• GT_I9300_unbrick_sdcard_head.zip - The BIN file used in Rebellos's method below.

1. Odin3 v3.07.exe and Odin3.ini
2. GT-I9300_Boot_Recovery.tar
3. (12-38)_GT-I9300_BRICKED.pdf.zip
4. External SD Card (Memory size should be 2GB or bigger.)
5. One normal I9300 phone(normally booted on)

• 
  Scenario: I bricked my phone and I want to fix it as mentioned in this thread. So I go ahead and look at the requirements:
  1. I download it from the attachments.
  2. I download it from the attachments.
  3. I download it from the attachments.
  4. I don't have one so I go buy one from a store for a little amount of money.
     [*]Ummmm... I have one but it can't boot... Damn! I don't have any friends that own one.... Damn! What should I do?!
     • Buy a new one so I can use it to fix the old one :silly:
     • Take my bricked phone to a store and pay at least 60$ for a fix.
     • Follow the instructions below.

• Because of the 'One Little Problem' there are a few things you can do ahead of time so if you brick your phone you will be prepared:
  1. If you don't own an extra one, buy a 2GB external SD card.
  2. Follow steps 1-12 in the manual using your own phone.
  3. Take the external SD card out of your phone and put it away in a safe place to be used if needed.
• Or follow Rebellos's (Elite Recognized Developer) way:
  

  Here's an experimental image: (Or attached to this post)
  https://dl.dropbox.com/u/32145655/GT_I9300_unbrick_sdcard_head.zip
  1) Insert SD card (Everything from it will be wiped!)
  2) Bootup some linux machine (it can be rooted android phone aswell as its also linux machine )
  3) Unpack archive
  4) Perform dd if=GT_I9300_unbrick_sdcard_head.bin of=/dev/<path to SD card device>
  
  On most of phones its /dev/block/mmcblk1 (MAKE SURE YOU DONT OVERWRITE YOUR INTERNAL PHONE MEMORY, ITS USUALLY "/dev/block/mmcblk0")
  
  On PCs it depends, its sometimes /dev/sdb
  More info about dding sd card:
  http://mikelev.in/2010/09/cloning-an-sd-card-on-linux/
  
  You're all ready and set, try to boot it up on dead I9300 and tell me how did it go! (Follow step 14 of Samsung's guide)
  
  Also, I don't think Anyway JIG is necessary. Probably you only need to connect it to PC so it gets powered and you can use download mode.

  Click to expand...

  Click to collapse

• This method of fixing your bricked device is only meant to be used if all else fails: Full S/W package with Odin (PIT, BOOTLOADER, PDA, PHONE, CSC) Or USB Jig.

mikep99 said:

Just been through actions 1-12 with no problems.
However, I can't see anything on internal/external sdcard that looks like a copy of the bootloader.
I'm assuming it's written to a part of the sdcard just like the 'goldcard' on the HTC Desire, which can't be seen without a hex editor.
This would then get picked up when using a jig?
Can anyone confirm this?

Sent from my GT-I9300 using xda app-developers app

Click to expand...

Click to collapse

Rebellos said:

Here's an experimental image:
https://dl.dropbox.com/u/32145655/GT_I9300_unbrick_sdcard_head.zip
1) Insert SD card (Everything from it will be wiped!)
2) Bootup some linux machine (it can be rooted android phone aswell as its also linux machine )
3) Unpack archive
4) Perform dd if=GT_I9300_unbrick_sdcard_head.bin of=/dev/<path to SD card device>

On most of phones its /dev/block/mmcblk1 (MAKE SURE YOU DONT OVERWRITE YOUR INTERNAL PHONE MEMORY, ITS USUALLY "/dev/block/mmcblk0")

On PCs it depends, its sometimes /dev/sdb
More info about dding sd card:
http://mikelev.in/2010/09/cloning-an-sd-card-on-linux/

You're all ready and set, try to boot it up on dead I9300 and tell me how did it go! (Follow step 14 of Samsung's guide)

Also, I don't think Anyway JIG is necessary. Probably you only need to connect it to PC so it gets powered and you can use download mode.

Click to expand...

Click to collapse

Odia said:

You did not need to flash the bootloader to your phone first, its only in the instructions in case the bootloader in the good GS3 does not support SDCARD write protocol.

I can confirm that using an SDCARD image to create the tweezer-tag SDCARD does work.

NOTE: Its also possible to write the entire OS to SDCARD, not just the bootloaders.

Click to expand...

Click to collapse

Rebellos said:

Flashing new bootloader is relatively safe (as far as reflashing bootloader can be safe)
It's just same set of bootloaders but with enhanced ODIN protocol - support of writing into T-Flash. As Odia said - recently produced I9300 models might have this feature in bootloader already.

No repartition should be used for these, new bootloader should overwrite old bootloader in working I9300, and during second flash present PIT will be used.

Click to expand...

Click to collapse

Rebellos said:

It can be said I added few steps after step 11 and before step 12 of Samsung guide.
Note: System must be rooted.
11.1) Bootup phone and connect it to PC
11.2) Invoke "adb root"
11.3) Invoke "adb shell dd if=/dev/block/mmcblk1 of=/storage/sdcard0/recovery_sd_head.bin bs=1024 count=4096"
11.4) Invoke "adb pull /storage/sdcard0/recovery_sd_head.bin"

You will endup with dump of first 4 megabytes of sd card. Should be enough to contain all necessary data to re-create bootable sd card from it.
Actually boot partition is ~880KB big so I guess dump of ~900KB should be enough. But better to have abit more and be more sure it'll work.

Click to expand...

Click to collapse

Rebellos said:

I've disassembled my I9300 yesterday and did some live tests on it.
Unfortunately I was unable to trigger EXT-SD boot, it's pretty hard to short only single resistor without shorting anything else and hanging the board or blowing something up. I'll retry it someday later when I get better tools. Maybe I triggered ext-sd boot but it didn't end up in any special screen because my device was fully alive.

Some tech background I worked out on that solution


Some good news:
If this is possible for SGS3, it's highly plausible that this such method of unbricking can be used for Exynos SGS2 models. This of course needs preparing another magic-SD card.

Click to expand...

Click to collapse

Net.silb said:

We've made it to the XDA Portal! (link below)

http://www.xda-developers.com/android/fix-your-soft-bricked-galaxy-s-iii-samsungs-way/

Click to expand...

Click to collapse

b-eock said:

Thanks for this

Sent from my GT-I9300 using xda premium

Click to expand...

Click to collapse

b-eock said:

This can only be done if you have the Samsung Anyway jig and no one on XDA has their hands on that yet. Or schematics of the board. We need an inside guy to leak that or even give us one.

Sent from my GT-I9300 using xda premium

Click to expand...

Click to collapse

b-eock said:

I am not here to argue, if we find a way to make the S3 unbrickable without the unbrickable mod. Then Awesome!!! Maybe this weekend we can talk about how things can be done. Until then I have football practice 6 outta the 7 days a week.

And I have that thread bookmarked bro

Click to expand...

Click to collapse